|
2.5ml eGo DCT Dual Coil Tube Kit (Holds 2.5ml eJuice | 1.7ohm & 2.5ohm) |
Fits all our eGo products - Designed specifically for use with eGo Electronic Cigarette batteries. New design screws onto your eGo battery and covers the battery threads for a finished look without having to have a skirt to cover the threads.
These are available in low resistance 1.7ohm and regular resistance 2.5ohm. Complete eGo Tube Tank kits with dual coil cartomizers to produce maximum flavor and vapor from your eGo Electronic Cigarette eCig.
Kit comes with;
1 - Tube Assembly
1 - Dual Coil Cartomizer insert
1 - 9.2mm Plastic Drip tip
** Note: VG Liquid does not work well as PG with Tank Tubes because it's much thicker and doesn't absorb into the cartomizer filler as quick. It will work, but you have to wait longer between puffs to allow the liquid to absorb into the filler.
Refill Instructions for the DCT (Dual Coil Tank)
- You will need the empty tube tank assembly and a bottle of liquid
- Remove the drip tip from the internal cartomizer
- Fill the internal cartomizer by dripping 25-30 drops of liquid around the edges into the fabric filler allowing time for the liquid to soak in. Be careful not to get liquid into the center hole.
- Slide the internal cartomizer partially out of the tube
- Drip liquid into the tube around the internal cartomizer. As it fills you can slide the cartomizer up to prevent liquid from going into the internal cartomizer. Fill as close to the top as you can get without allowing the liquid to leak into the internal cartomizer.
- Slide the internal cartomizer back into the top sleeve of the tube tank and align the bottom (thread end) with the slot on the end of the tube tank so it's fully inserted into bottom of the tube tank.
- Replace the drip tip. You'll need to apply pressure to the bottom of the internal cartomizer while pushing the driop tip on to prevent the internal cartomizer from sliding out of the tube tank.
- Screw onto your device and you're ready to use the tank tube assembly.
Top 10 Things You Need to Know About Using and Caring for your Electronic Cigarette
1. Never charge your eCig batteries before they are dead. Batteries are dead when the LED on the tip of the eCig battery flashes immediately every time you attempt to take a puff. - If the eCig battery has no charge at all the LED light will not illuminate when you try to take a puff which also indicates the eCig battery needs to be charged.
- Don’t mistake the over usage indicator for a dead ecig battery. If you take too long of a puff (over 10 seconds) or too many puffs in a 60 second period the LED on the tip of the eCig battery will flash to warn you it is being over used.
- To ensure the flashing is due to a dead eCig battery you should make several attempts to take a puff and if the LED on the tip of the eCig battery flashes immediately with every attempt the eCig battery is dead and needs to be changed.
- Clean the threads on your electronic cigarette battery and charger before charging and be sure not to over tighten the electronic cigarette battery in the charger. Screw the eCig battery into charger until you feel resistance and that is tight enough. Screwing the electronic cigarette battery in too tight can damage the connectors causing damage to the eCig battery and/or charger.
- Do not use the Electronic Cigarette PCC (Portable Charging Case) to charge eCig batteries if you have access to charge with the normal electronic cigarette USB charger.
- Remove the eCig battery from the charger as quickly as possible after charging is complete and never leave a charging battery unattended.
2. Always keep your eCig threads clean. Wipe the threads clean on your eCig battery, atomizer, charger, and cartomizers every time you change or refill an eCig cartridge and before each charge. - Not doing this can cause a short resulting in the eCig device or charger no longer working.
- Damage due to dirty threads or liquid in the battery or charger are not covered under our warranty. Batteries or chargers returned to us with dirty threads or liquid in them cannot be replaced.
3. Never charge your eCig PCC with an eCig battery screwed into the charging slot on PCC and only use the PCC when you do not have access to your normal USB eCig charger. - The electronic cigarette PCC will not attempt to charge an eCig battery unless it is completely dead and it only gives the eCig battery an 80% charge to prevent over charging.
- Do not over tighten the electronic cigarette battery in the charging slot of electronic cigarette PCC. Screw it in until you feel resistance and that’s tight enough.
- Over tightening the eCig battery can cause damage to the PCC and/or the battery connectors rendering them unusable.
4. Remove eCig cartomizer from battery before refilling and always disassemble the eCig when not in use or when storing. - It’s best to store your electronic cigarette device in a carrying case or electronic cigarette PCC to protect it from damage. Leaving the eCig device assembled when not in use can damage the battery, atomizer, and/or cartomizer and if you have liquid in your battery from overfilling it could activate automatically and cause damage.
- Getting liquid in your battery is very easy to do if you don’t follow the refill instructions and/or leave the electronic cigarette device assembled while not in use or while filling.
- Failures due to dirty threads or liquid in the electronic cigarette battery are not covered under our warranty. Batteries returned to us with dirty threads or liquid in them cannot be replaced.
5. Always wipe excess liquid off of eCig batteries, atomizers, and cartomizer threads after refilling. - Not removing the excess liquid from your electronic cigarette battery and cartomizer threads can result in damage to your eCig battery and/or cartomizer causing them to be unusable.
- Failures due to dirty threads or liquid in the battery are not covered under our warranty. Batteries returned to us with dirty threads or liquid in them cannot be replaced.
6. Take long (3 – 6 second), soft puffs from your eCig to produce the best flavor and vapor - If you take short and hard puffs the electronic cigarette device will not function properly.
- If you take over a 10 second puff the LED on on the tip of the electronic cigarette battery will flash indicating you have taken too long of a puff. Do not mistake this flashing for a dead battery.
7. When using 3 piece design eCigs (non cartomizer style) twist eCig cartridges when removing to make them easier to get off eCig atomizer. - Do not try to pull the eCig cartridge straight off because it can pull the atomizer apart.
- Twisting is as you pull will make it come off easier and reduce the chance of atomizer damage.
8. Never use with a dry eCig cartridge or eCig cartomizer. It only takes a few puffs with a dry cartridge to burn up the atomizer. Never take a puff on your eCig with a blank electronic cigarette cartridge/cartomizer attached before it’s been filled because 1 puff will burn the filler making it unusable. Follow these simple steps when refilling cartomizers. - Cartomizers
- Filling our standard (1ml) cartomizer will take 20 - 25 drops of liquid. If your cartridge or cartomizer has a larger capacity than 1ml determine how many drops are required for filling based on 20-25 drops per ml.
- It should take 3 - 4 minutes to fill it so it has time to soak into the filler.
- Remove the cartomizer from the battery, remove the white rubber end plug, then put a couple of drops of liquid around the edges so it runs into the filler (be careful not to get in center hole), rotate 1/4 turn, wait 10-20 seconds, put 2 more drops, and continue repeating the process until the liquid puddles up on top of the filler.
- At this point it's a good idea to wrap a paper towel around the thread end of the cartomizer and blow lightly through the mouth piece end to remove any excess liquid.
- Lastly, wipe the threads on the battery and cartomizer clean with a paper towel and you should be good to go.
- Cartridges (Type without built in atomizer – just a plastic cartridge with filler material and no threads)
- When using a 3 piece design model (battery, atomizer, and cartridge). Follow these steps for refilling.
- Remove the cartridge from the atomizer
o For best results you should remove the filler from cartridge.
- Fill liquid capsule ¾ to top with liquid.
o Carefully and slowly replace the cartridge filler.
- Wipe any excess liquid from the outside of the cartridge.
- Insert cartridge back on atomizer and you are ready to vape.
- Clearomizers & Tanks - Depending on the type of Clearomizer or tank you have the refilling instructions vary. Please visit the product on our site for specific instructions for the type you have.
- For CE4 & CE5
- Remove the Clearomizer from the eCig battery then remove the drip tip.
- Remove the drip tip
- Tilt the Clearomizer slightly then drip liquid down the side of the inside wall. Be careful not to get liquid in the center hole.
- Fill with liquid to the bottom of the clear rubber cover around the atomizer head. Filling past this point will cause flooding and leakage.
- Replace the drip tip and screw clearomizer back onto battery
- Vision ViVi Nova
- Remove the Nova tank from the ecig battery
- Unscrew the top cap on the tank
- Tilt the tank slightly then drip liquid down the side of the inside wall. Be careful not to get liquid in the center hole
- Fill with liquid to the bottom of the clear rubber cover around the atomizer head. Filling past this point will cause flooding and leakage
- Screw the top cap of tank back on and it is ready to use.
- DCT (Dual Coil Tank)
- Remove the DCT from the battery then remove the drip tip
- Slide the internal cartomizer down until it is about ¼” below the top cap on tube
- Tilt the DCT slightly then drip liquid down the side of tube until liquid is at the top of internal cartomizer
- Slide the internal cartomizer back through top cap
- If this is the first time filling the DCT you will need to fill the internal cartomizer with 25-30 drops of liquid dripped around the edges into filler material
- Replace the drip tip and wrap a paper towel around the thread end of DCT, blow lightly through the DCT from the mouthpiece end to remove and excess liquid
- The DCT is now ready to use.
9. Don’t over-tighten the eCig battery on the eCig atomizer/cartomizer, in the eCig charger or eCig PCC. Screw it in until you feel resistance and that’s tight enough. - Over tightening will damage the connectors in the battery causing it to fail and voiding the warranty.
- Sometimes there may be a small gap between the cartomizer/atomizer and the battery which is normal. Do not try to tighten until the gap is gone because it will damage the connectors causing the device to fail and void your warranty.
10. If the LED light on the tip of your eCig battery activates without taking a puff, the eCig battery and/or cartomizer get warm when you assemble them without you taking a drag, or the eCig atomizer/cartomizer activates by itself when you screw onto battery you most likely have liquid in your eCig battery from over filling the cartridge or the threads on your eCig device are dirty. - You can try to remove the liquid from the eCig battery using a can of compressed air by blowing the air into the thread end of the battery.
- You can also clean the threads on your battery with a paper towel to see if it corrects the problem.
- If after cleaning, the battery still activates itself or causes the cartomizer/atomizer to get hot when assembled do not attempt to use the device, disassemble it and dispose of properly.
- If the problem still exists you will need to replace the eCig battery.
- To prevent the issue be sure not to over fill the eCig cartridges, never refill with cartridge attached to battery, and be sure to always keep the threads clean on your battery, cartomizers, atomizers, and chargers.
- Failures due to dirty threads or liquid in the battery are not covered under our warranty.
- Batteries returned to us with dirty threads or liquid in them cannot be replaced.
Quality AquaVapor Cig Electronic Cigarette / eCig Accessories and Supplies
We take great pride in and are committed to quality customer service and quality eCig products. We go the extra step to ensure our Electronic Cigarette / eCig products are the best available on the market. As mentioned on the About Us page, we've tested hundreds of Electronic Cigarette / eCig models and if it's not good enough for us (17+ year smokers) it's not good enough for us to market and sell to you. We work closely with our manufacturer, who is the leading Electronic Cigarette / eCig manufacturer in the world to continuously improve the eCig products we sell. You have the promise from Aqua Vapor Cig that you will get the highest quality Electronic Cigarette product available for the most competitive price, guaranteed!
| |
Didn't have to buy a skirt to fit my ego v. Filling has a little learning curve to it without a needle tip bottle. Vapor production is good and you can really taste the flavors of your juice. Low ohms is perfect for extending my 650mah to all day use. Seals hold up pretty good after a month of daily use and refilling. |
| |
Reviewed by: Leo Napuli from Glendale, CA.
on 3/24/2013
5/5 |
|
 |
| |
This has been the most dependable tank that I have ever used, no flooding, no dry hits and looks cute as can be on my eGo battery! Hopefully they will keep selling this product because I am a customer for life! |
| |
Reviewed by: Casey Greeson from Dawsonville, GA.
on 3/4/2013
5/5 |
|
|
| |
I was just using the ego c regular cartomizer and thought I would try this. So glad I did. Wonderful vape and flavor enhancement..So much more enjoyable with this tank. Perfect size. The gray looks good with the black battery and I am very happy! |
| |
Reviewed by: Philip Paris from Stafford Springs, Ct..
on 3/1/2013
5/5 |
|
|
| |
I got this to go with my Gripper and with the 510 extension it works amazingly. I Have noticed that it even makes the juices taste even better. I will for sure be buying these regularly. |
| |
Reviewed by: Donnie McAbee from North Carolina.
on 2/13/2013
5/5 |
|
|
| |
I bought this in lime green. I usually use 510 clearomizers, but this is great as well! The flavor of the eliquid was very clear and the vapor was great! A+++ |
| |
Reviewed by: Jessica McCourt from WV.
on 2/12/2013
5/5 |
|
|
| |
Good Product, Just be careful when refilling. Easy to pull the tube out completely. Like the 3.5 better, they are easier to fill. But these are good if the smaller size is needed... |
| |
Reviewed by: James Stabene from Jamison Pa.
on 2/11/2013
4/5 |
|
|
| |
Since I got my Ego model, I've been trying all of the different types of juice delivery methods. This one is definitely up there. It's not my favorite, but it is very nice.
Pros: Good capacity, great vapor production and flavor.
Con: Pain to fill compared to some of the other models. (This isn't to say that it's awful to fill, its just more involved then the ce4/5 and vivi nova.)
Still great, and I would highly recommend if its something you are interested in. |
| |
Reviewed by: Troy McNeil from Ohio.
on 12/16/2012
4/5 |
|
|
| |
I got this for several reasons one I have another dct made by a different company and I wanted to compare the two designs for one. Second concerns the design I like the way it fits on my devices no need for extra thread covering cones ect... Last but not least it came in the color of my mini battery paired with a dark blue anodized drip tip also available from AVC and I'm vv wooing in style. This baby produces great clouds of vapor and the flavor is spit on due to the dual coil action going on. I'm going to be picking up a few more these to be sure. |
| |
Reviewed by: John Dearing from Akron, Ohio, USA.
on 11/17/2012
5/5 |
|
|
| |
I have been vaping for a coulpe years now and I've tried a lot of different products. I have been using the eGo with tank atomizers and decided to give these a try. I'm glad I did, they are very easy to use and the vapor and flavor is amazing. Shipping was extremely fast. |
| |
Reviewed by: Jacob from Kansas.
on 11/11/2012
5/5 |
|
|
| |
These are absolutely the best DCT's! I ordered two of these on my last order almost 6 weeks ago and they are still going strong! So easy to refill and I have never had one leak. I just ordered two more as spares! These produce huge vapor and I only have to fill them at most twice a day! I vape pretty heavy, these have held up better than any others I have bought! Great product Aqua Vapor! Please keep these in stock! |
| |
Reviewed by: Thomas Shrader from Bayou Vista, Texas.
on 11/8/2012
5/5 |
|
|
| |
Ok so I got one of these and it is definately awesome! Tons of vapor and less babysitting my ecig! I slap one on my ego battery and Im good to go all day! Haven't had any issues with leaking at all. Seriously, you need to get one! |
| |
Reviewed by: Tricia : ) from Ohio.
on 10/23/2012
5/5 |
|
|
| |
Nice finished look for Ego batteries.Lots of vapor.Note,you must buy the carts that fit this tank, 3.5ml carts don't fit, the flange on the bottom of 3.5 is wider and wont go in all the way, also it will only take about 1.2ml + what gets absorbed in the cart.Not recommended for heavy vapors.But still a good tank, My wife loves it. |
| |
Reviewed by: jeff from St louis.
on 7/23/2012
5/5 |
|
|
| |
These are my first dual coil cartomizer tanks. After a few trial and errors learning how to fill them, I love them! No more refilling every hour! The look really good on my new Ego Twist, too. Now, I'm off to buy the 3.5 ml dual coil cartomizers! Aquavapor rocks! They always aim to please their customers and have always done right by me! |
| |
Reviewed by: Diane from California, USA.
on 7/8/2012
5/5 |
|
|
|
|
